web analytics
Add to wishlist

L2900 2-Post Lift 9,000 Lb Capacity Car Auto Truck Hoist 220v Or 110v

$749.00

The L2900 Two Post Lift is a car lift designed for automotive service and repair shops. It has a lifting capacity of 9,000 lbs

L2900 Two Post Lift 9,000 Lb Capacity Car Auto Truck Hoist 220v Or 110v

The L2900 Two Post Lift is a car lift designed for automotive service and repair shops. It has a lifting capacity of 9,000 lbs, making it suitable for a wide range of vehicles. The lift features a two-post design, allowing for efficient use of floor space, and its hydraulic operation provides smooth and controlled lifting. It is available in both 220V and 110V versions and its heavy-duty construction provides reliable and long-lasting performance. The lift is designed to make maintenance and repair work on vehicles more convenient and efficient.

Features:

Safety Mechanism:

  • Double Point Safety Lock Release
  • automatic Arm Lock Restraints
  • relief Valve Built In Power Pump To Prevent Overloading
  • door Guards Protection Rubber
  • up-limit Switch To Protect Cylinders Working Stroke Used In Safe Length Scope
  • heavy Duty 5/16″ Diameter Cable And 4.56″ Pulley Reduce High Stress On Synchronization Process And Increase Cable Life
  • stiffened Base Plate 15/32″ Thickness
  • ultra High Molecular Self Lubricating Nylon Slider Ensures Carriage Smooth Moving Up And Down
  • anchor Bolts/mounting Hardware Included

Control System:

  • Lifting Operation By Pressing “Up” Button On Motor
  • manual Lowering Operation By Pressing Lever
  • relief Valve Built In Power Pump To Prevent Overloading
  • 1 Sets Truck Adapters Included
  • lifting Capacity: 9,000 Lbs
  • the Overall Height 111-3/32″
  • the Overall Width 133-1/4″
  • column Width 10.59″

width Between Two Post 106.3″

  • Base Width 18.89″
  • column Thickness Of Steel 11/64″
  • carriage Thickness Of Steel 3/16″
  • arms Thickness Of Steel 15/64″
  • front Arm 29.9″-47.2″
  • rear Arm 29.9″-47.2″
  • min Pad Height: 3-7/8″
  • lift Height Max: 71.6″
  • drive-thru Width Clearance: 99.2″
  • Time To Full Rise: 20-60 Sec
  • Shipping Weight: 1150 Lbs

Before Installing Your Auto Lift, Check The Following:

Lift Location: Always Use Architect’s Plans When Available. Check Layout Dimension Against Floor Plan Requirements Making Sure Adequate Space Is Available. Your Lift Requires A 220v Or 110v , 30amp, Single Phase, Grounded Electrical Source. There Should Be Room Enough To Operate The Lift In A Safe Manner And Without Restrictions.

Overhead Area: The Area Where The Lift Will Be Located Should Be Free Of Overhead Obstructions Such As Heaters, Building Supports, Electrical Lines, Doors, Lights, Etc.

Floor Area: Visually Inspect The Site Where The Lift Is To Be Installed And Check For Cracked Or Defective Concrete.

Floor Requirements:

A Level Floor Is Suggested For Proper Installation And Level Lifting. Small Differences In Floor Slopes May Be Compensated For By Proper Shimming. If A Floor Is Of Questionable Slope, Consider A Survey Of The Site And/or The Possibility Of Pouring A New Level Concrete Slab.

  • New Concrete Must Be Adequately Cured For At Least 30 Days.
  • Do Not Install Auto Lift On Any Asphalt Surface Or Any Surface Other Than Concrete.
  • Do Not Install Auto Lift On Expansion Seams Or On Cracked Or Defective Concrete.
  • Do Not Install Auto Lift On A Second/elevated Floor Without First Consulting Building Architect.
  • Do Not Install Auto Lift Outdoors Unless Special Consideration Has Been Made To Protect The Power Unit From Inclement Weather Conditions.

Concrete Specifications:

  • All Models Must Be Installed On 3,000 Psi Reinforced Concrete Only. Additional Concrete Requirements Will Vary By Lift.
  • 8,500 Lbs – 10,000 Lbs Lifts: 4? Minimum Thickness
  • 11,000 Lbs – 15,000 Lbs Lifts: 6? Minimum Thickness

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.